Boiler feedwater check valves face 700–1,400 PSI pressure swings, temperatures to 350°F, and continuous high cycling. Standard swing checks fail in months. DFT's WLC BF is engineered specifically for this application.
#BoilerFeedwater #PowerGeneration #CheckValves
3
Vertical flow-up piping in mine dewatering systems requires check valves that don't rely on gravity to close. DFT spring-assisted check valves close consistently in any orientation, preventing reverse flow & water hammer at pump shutdown.
#Mining #CheckValves #WaterHammer
1
1
27
High cycling destroys standard swing check valves, often within months. In digester and boiler feedwater service, DFT severe service check valves with upgraded 17-4 trim and X-750 springs deliver years of service life instead.
#SevereService #CheckValves #ReliabilityEngineering
1
2
26
Vacuum conditions cause condensate backup, siphoning, and pressure vessel collapse. The DFT Vacuum Breaker allows air in to relieve vacuum and break siphons, 1" to 4", up to 6,000 PSI, liquid and steam service. 🎥
#CheckValves #VacuumBreaker
1
2
78
The DFT SCV, ½" to 3", 750 and 3,600 PSI, liquid, gas, and steam service. Stainless steel, Inconel X750 spring, silent non-slam closure, ready to install in any orientation 🎥
#CheckValves #SCV #ValveEngineering
2
147
The DFT SCV-R inline restrictor check valve, ½" to 2", NPT or socket weld ends, Inconel X750 spring, silent non-slam closure for high back-pressure liquid and gas applications. 🎥
#CheckValves #SCVR #ValveEngineering
2
83
The DFT Restrictor Check Valve, ¼" to 2½", up to 2,500 PSI, cracking pressures from 2 to 40 PSI. Spring-assisted silent closure for liquid and gas applications that demand higher opening resistance. 🎥
#CheckValves #RestrictorCheck
2
135
The DFT Basic-Check valve, ¼" to 2½", up to 6,000 PSI, liquid, gas, and steam service. Silent closure, stainless steel construction, internal spring rated for over 1 million cycles.
See how it's built. 🎥
#CheckValves #BasicCheck
1
95
Compressor discharge is high pressure, pulsating, and unforgiving. The DFT Excalibur closes before flow reversal occurs, provides tight shutoff, and is built for a million-cycle service life in severe service applications.
#CheckValves #CompressorDischarge #SevereService
1
39
Gravity-dependent check valves struggle in vertical flow-down installations. DFT in-line check valves are rated for any orientation, horizontal, vertical up, or vertical down, with consistent spring-assisted closure in every position.
#CheckValves #PipingDesign
1
36
Gas transmission exposes check valves to pulsating compressor discharge, pressure swings, and corrosive gas compositions. DFT check valves are engineered for the specific demands of these applications, not adapted from general-purpose designs.
#GasTransmission #CheckValves
2
38
Standard check valves aren't built for reciprocating compressor discharge. Each stroke creates a momentary flow drop that accelerates seat wear. The DFT PDC's pulse damping chamber holds the disc open through every cycle.
#CheckValves #CompressorProtection
2
95
Water hammer generates pressure spikes up to 10x normal system pressure. Check valve type is often a direct cause. Spring-assisted valves close before flow reversal — stopping the shockwave at the source.
hubs.la/Q04nqj-D0
#CheckValves #WaterHammer
3
776
Compressor systems are sensitive to pressure changes during flow transitions.
Valves that rely on reverse flow to close can introduce vibration and stress.
DFT spring-assisted check valves close earlier, helping stabilize compressor systems.
#CompressorSystems #FlowControl
27
Flow path design impacts system performance.
Axial-flow check valves align with flow direction, helping reduce turbulence and support stable pressure.
DFT check valves can be installed in vertical flow up and vertical flow down orientation.
#AxialFlow #FlowControl
37
Pump shutdown doesn’t stop flow instantly. As velocity decays, pressure transients can create vibration and stress.
Delayed valve closure allows reverse flow and stronger pressure spikes. DFT check valves respond earlier to help stabilize system performance.
#FlowControl
1
38
Reverse flow can begin within milliseconds after pump shutdown.
If a check valve closes too slowly, returning fluid can cause slaming, vibration and pressure spikes. Spring-assisted valves respond quickly, helping stabilize pump discharge systems and protect piping.
Remembering and honoring those who gave their lives in service.
Their sacrifice is not forgotten.
#MemorialDay #HonorAndRemember
1
13
In fluctuating flow conditions, waiting for reverse flow to close a valve can lead to instability.
DFT’s spring-assisted check valves begin closing as flow decreases, helping reduce slam and stabilize pressure.
#NonSlamValves #FlowControl #CompressorSystems
1
18















