Jon Hammack (@JonHammack) header
Jon Hammack (@JonHammack) profile picture

Furniture/wood work https://nitter.cf/t.co/IBEv9fI4g3

Edmond, OK
Joined March 2011
Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)Photo by Jon Hammack (@JonHammack)
Increasingly have less and less to say here. Definitely feels more like doom scrolling every time I open the app, so I’m locking, unfollowing everyone minus Destiny 2 official accounts since that’s still the easiest way to stay up to date, and won’t be posting anymore.
1
1
214
If you like my woodworking stuff, I’ll still be posting that to insta. DMs are also open, or you can hit me up on discord.
3
135
Waiting on drawer hardware, so it was the perfect time to make a tool: a sector. Essentially just two sticks attached with a hinge (between 2-3ft long), divided into 13 equal sections (stepped out from the rear of the hinge pin).
1
145
It’s used to get proportional measurements from things without the need of math/unit based measurements. Line up the ‘10’s on the bottom corners of a drawer front, and then I can set my dividers to span across the ‘2’s, giving me a 1:5 proportion.
1
79
1/5th the face width is the traditional spacing for drawer knobs. That plus 4/7ths the drawer face height gives a proportional location for knobs/pulls. Just one of many uses of the sector.
59
Fit all the drawer bottoms today. I love the dichotomy of working on them. I never clean up the underside of the panels (and even go so far as to leave glue squeeze out) because it will never be seen but I hand bevel the slot for the screw to match the countersink with a chisel.
1
115
156
3,717
193
44,489
1,891,080
Milling pine for drawer bottoms today. Bag was empty when I started, but the garage smells nice. All that’s left is to trim to width and glue up the panels.
1
95
This was nice and flat when I pre-milled the drawer stock. Fucking poplar.
3
1
240
Little over an hr later and the sides have a flat face an edge again (need a trip through the planer to get to final size). Sticking with maple in the future 😅
61
Dyed the base, dyed the bottom of the case, and milled the back boards. This poplar has been extra twisty, so I’m pivoting to tongue and groove instead of shiplap. Tomorrow I need to make another batch of furniture finish and start making drawers.
1
91
Mocked up a few different feet using scrap (hence the rough faces). 3:2, 2:1, 3:1 ratios. Up close the 3:1 taper looks interesting but 2:1 feels right when I step back. The client is still in school, so I’ll have to wait to confirm. The square foot was his original request.
2
3
183
After looking at it to scale, Reid decided he liked the largest taper (as opposed to the square foot) and also decided to inset the base. Parts are marked and prepped for tomorrow.
56
I lost motivation to continue because drawing guardians is hard. But you get the idea. #destiny2 #guardiandown #theregoesflawless
1
1
149
22 mortises done. Not a bad way to spend an afternoon. Tomorrow (weather permitting) I’ll cut 11 runners and the corresponding tenons.
1
82
Web frame parts finished yesterday so it’s time to make a lot of mortises.
1
70
Rest in Peace, Commander.
1
7
237
Starfire warlocks after today’s patch notes (of which I am one of them). Shop courtesy of @livewire11211
1
1
1
161