Open Source Arms (@OpenSourceArms) header
Open Source Arms (@OpenSourceArms) profile picture

Open Source Arms maintains an open technical database of standardized testing, manufacturing practices, and technical data packages of tested firearm designs.

Joined August 2026
Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)Photo by Open Source Arms (@OpenSourceArms)
Open Source Arms retweeted
A rebellion built on hope. free files plastic parts nuts and bolts barrel made with a bucket of water hair product can Now you have hope and a 3D printed integrally suppressed submachine gun.
24
164
8
1,951
39,078
Open Source Arms retweeted
Time the print so that stage happens while you're sitting right next to it, so everything stays hot. Maybe even keep your inserts on the floor of the printer so they're warm when you insert them instead of cold-shocking your print.
3
1
10
231
Open Source Arms retweeted
I guarantee this is the weirdest gun you鈥檒l see today. Featuring the new 9mm hush puzzle.
19
26
441
9,182
Open Source Arms retweeted
Now with candy corn baffles in PLA orange
1
7
26
504
Open Source Arms retweeted
As a mockup, this goes extremely hard, but I would need to find a 9mm mag body that can fit within the mock ak mag to make it feed right
7
3
1
48
2,517
Open Source Arms retweeted
Your move @emm0sh
i'm actually making this courtesy of sendcutsend i'm starting with a 1:8 prototype
39
23
5
936
61,647
Open Source Arms retweeted
9
94
2
1,400
30,881
Open Source Arms retweeted
Replying to @ArthurClaudeen
Yes. TPU (And PETG) bond super hard to PEI because of the differential between their respective molecular sizes, among other things. Textured PEI actually reduces the bond, but it's still very strong. In fact, using flat/glossy PEI with TPU, you actually need a release agent (Like a thin layer of vegetable oil or something) on the PEI before you start your print or you'll be tearing off chunks of your bed to get the print off. Because the TPU is being squirted onto the bumpy surface, it's not actually in contact with every nook and cranny, and is really only touching about half of the PEI. This leaves tens of thousands of tiny gaps between your TPU and the PEI sheet. Alcohol is a very thin liquid, (Low viscosity) thinner than water. Flooding the PEI, a quite dense, liquid resistant material, with alcohol makes it super slick almost instantly, OTOH the TPU with it's lower density molecule tends to instantly (Temporarily) drink the alcohol up into the outermost edge of it's surface. Because of all those little gaps from the bumpy surface, the thin alcohol flows right under your print super fast. Between the two materials getting hit with the alcohol, the TPU almost automatically wants to pop right off. And like I said, this also applies to PETG if you print your first layer a little wide for extra adhesion and it gets really stuck.
4
2
23
399
Open Source Arms retweeted
I GOT WRECKED AT FINNISH BRUTALITY!! | Brutalized in Finland Ep. 2 OUT NOW, LINK IN BIO
1
1
6
300
Open Source Arms retweeted
For those of us printing CF Nylon the right way it's a real test of patience.
16
2
1
167
4,276
Open Source Arms retweeted
If you aren鈥檛 following this project yet, you really should check it out!
1
3
150
Open Source Arms retweeted
Legal, semi-automatic, ghost gun 馃懟 馃懟 馃懟 Check out version V1.1 of the amazing M1337 by @Nopel_0 Pricey build, but it likely represents the most advanced GunCad project the community has ever seen.
10
26
1
278
6,044