Jim Drygiannakis (@jdryg) header
Jim Drygiannakis (@jdryg) profile picture

Nothing to see here. Move on. There are other more interesting accounts to follow out there.

Athens, Greece
Joined August 2010
Work in progress
4
3
15
Jim Drygiannakis retweeted
DLS in now free (name your own price) on itch.io makingartstudios.itch.io/dls
1
1
129
Today I’m releasing the source code of my new experiment - multi-threaded, CPU-based vector graphics rasterizer - github.com/aurimasg/blaze
2
30
1
167
23,401
Triangle Rasterization - Part 2: More optimizations cohost.org/jdryg/post/625373… TLDR: Managed to save ~0.4ms (1.34ms/frame -> 0.94ms/frame) using only SSE2 and ~0.5ms (0.82ms/frame) using SSSE3/SSE4.1
3
24
3,030
Trying to optimize a simple triangle rasterization function I found on the internet. cohost.org/jdryg/post/603959…
2
What's the proper way to handle rendering on minimized window? Render to a 1x1 framebuffer and swap/vsync as you normally would? Skip rendering completely and Sleep(16)? Something else?
3
Electronics Twitter: My brother had an idea to replace the analog dashboard of my father's tractor with an LCD display. Does anyone have any recommendations on an mcu/fpga/soc + 10"-11" display with support for 60Hz refresh rate + a couple of sensors? Fast boot up is a plus.
1
1
This looks interesting: crowdsupply.com/excamera/gam… Anyone has any experience with it? Is it suitable for rendering a simple UI (e.g. a tractor dashboard :))?
1
Another alternative might be a Zynq board like this: aliexpress.com/item/40003235… Has HDMI + ADC for analog sensors + an ARM core for the app/UI.
Had an idea to try setjmp/longjmp with a SIGSEGV signal handler to overcome a crash when calling a specific function from a 3rd party DLL. It seems to work (no crash when calling the func), but unfortunately sentry/crashpad stops working, even though I reset the signal handler.
1
It turns out it's a bit more complicated. Even if sentry/crashpad kept working correctly, the DLL ends up in an invalid state and has to be reinitialized (takes time). Also, I'd have to limit access to the DLL to a single thread because calling a function during reinit will fail.
1
The DLL is a WinUSB wrapper ("driver") for a device with an I2C bus. The crash can be reliably triggered when trying to read data from the I2C bus when no I2C device is present. In production, the I2C device appears as disconnected after a long period of inactivity.
Initial attempt to convert NV12 to RGBA using SSE2. ~2x speed up compared to original C code, (1280x720 image). The original C code could probably be made faster without relying on SIMD but where's the fun in that :) gist.github.com/jdryg/670315…
3
Jim Drygiannakis retweeted
After almost 3 years of inactivity, v0.17.0 is live on itch.io. It includes an experimental transistor-level simulator and various bug fixes. makingartstudios.itch.io/dls
1
4
17
Switched to a more generic Kalman filter equ and implemented a simple genetic algorithm for auto-tuning all motor driver parameters. Blue: Dirt Rally 2.0 FFB torques Red: Raw motor current (actual wheel response) Green: Filtered motor current (PID input) nitter.cf/jdryg/status/145666549…
Replying to @jdryg
I now have everything needed (theoretically) to try and tune the PID controller and sensor filter. Force recording and playback using HID.dll and a metric to compare different configurations (integral of absolute error).
Wrote a small app using ImGui + ImPlot to visualize my FFB wheel's PI controller output while playing Dirty Rally 2.0, because Serial Oscilloscope was too slow and kept crashing all the time.
2
3
Note to future self: Since this is an HID device, a custom feature report (UsagePage=Vendor) is enough. (HidD_SetFeature/HidD_GetFeature) No extra interface or device is required and the CDC can stay independent of the HID device.
1
I now have everything needed (theoretically) to try and tune the PID controller and sensor filter. Force recording and playback using HID.dll and a metric to compare different configurations (integral of absolute error).
I also added a stack of equations to the app. Each equation can take as input all the avail. channels (data coming from the mcu over the CDC/UART) + all the equation results above it. A simple way to try out various configs to see how they affect sensor raw data.
1
Currently I have simple binary ops (+,-,*,/), low and high pass filters and the simple Kalman filter I have implemented in the mcu. I was tempted at some point to turn it into a node graph (using ImNodes) but I discarded the idea. Too much work. A stack is fine for this.