When a machinist says "a tenth," they DON'T mean 0.1 inches! ๐คฏ
They mean 0.0001 inches โ a tenth of a thousandth.
Mix those up and you're going to have a VERY interesting conversation with the machine shop. ๐
#Machining #Metrology
1
58
Think pin gauges are expensive? ๐ธ
This entire set from Haas Tooling cost us about $176!
We use these regularly for checking hole sizes. Precision measurement doesn't always require a huge budget.
Not sponsored. Just what we use! ๐ง
#Machining #Metrology
53
We had so much leftover metal that our workbench BROKE! ๐
Atlas Shelving sent us a rack to review. Six bins weighed 390 lbs, and we estimate ~half a ton total! ๐ณ
๐ฅ buff.ly/rPpn8Pd
Free review unit; opinions our own. Affiliate link may earn commission.
41
Why buy pin gauges when you've got drill bits? ๐ค
Because they're NOT the same!
Drill bits work for rough hole-size checks, but precision machining calls for tightly toleranced pin gauges.
Right tool, right job. ๐ง
#Machining #Metrology
117
A drawing calls for a 1-inch-deep hole. Does that include the drill tip?๐ค
Generally, NO! Blind hole depth is measured to the full-diameter portion.
Even NASA's fabrication guidelines spell it out.
What drawing conventions cause confusion in your shop?
#Machining #Engineering
34
Our metal drops got so heavy they BROKE the workbench! ๐ณ
We upgraded to an Atlas Shelving rack, sorted the stock, and weighed the bins.
๐ฅ Full video: buff.ly/rPpn8Pd
#Machining #ShopOrganization
22
My flashlight still works as a shop tool when the battery is DEAD! ๐ฆ๐งฒ
I use its charging magnet to check whether scrap metal is magnetic, then use weight and density as extra clues.
A handy trick for sorting metal drops!
#Machining #ShopTips
30
๐จ CHECK YOUR HALLOWEEN CANDY! ๐ฌ
We found an entire 1997 Sharp surface grinder attached to ours.
Can you imagine if someone tried to eat that?! ๐๐
Some people are just sick, man.
#Halloween #Machining
Shop superpower unlocked! โก
Identify coil pairs on a disconnected 4-wire stepper motor with NO tools!
Twist two wires together and turn the shaft. More resistance? You've found a pair!
๐ฅ Full wiring tutorial: buff.ly/dh4Zi8A
#StepperMotor #Engineering
20
Shopping for a geologist? ๐๐
A Rite in the Rain notebook is a fieldwork classic! ๐
Take notes in wet conditions and keep those important rock descriptions and instrument readings.
๐ Available in our store: buff.ly/qsnwgOn
What's on your field gear wish list?
18
Flat or vertical? ๐๏ธ
We 3D printed the same landscape both ways to compare detail, layer lines, and surface finish.
Bonus: Students use these models with water to learn topographic maps! ๐ง
Which would you choose?
#3DPrinting #STEM
23
Stepper motor with no wiring diagram? โก
You can identify the coil pairs on a 4-wire motor WITHOUT a multimeter!
We also cover 6-wire center taps, resistance testing, and troubleshooting.
๐ฅ Full tutorial: buff.ly/dh4Zi8A
#StepperMotor #Electronics
14
I touched a precision gauge without gloves. Again. ๐๐งค
Nitrile gloves help keep oils off. Cotton gloves help limit heat transfer. Shop-floor gauges aren't always treated like final inspection sets.
The right choice depends on the application.
Team gloves or bare hands?
1
43
Water flows downhillโฆ so why is it moving UP? ๐คฏ๐ง
Our groundwater teaching kit uses dye and sand to show how water and pollution move underground.
Clear water doesn't always mean clean water.
Would you put a well here?
๐ buff.ly/MjMx2o9
#Groundwater #STEM
1
29
Silica gel vs. molecular sieve! ๐ง
We tested which desiccant removes moisture faster and how dry each can get a sealed container.
One had an early lead, but what happened over the full test?
๐ฅ Watch the experiment: buff.ly/Gm0VSKX
#Engineering #Science
20
One stray wire strand can short out your project! โก
Wire ferrules keep stranded wires together for cleaner, more reliable terminal connections.
Strip, insert, crimp. Simple!
Do it nice or do it twice. ๐ง
Do you use ferrules?
#Electronics #Engineering
25
Silica gel vs. molecular sieve! ๐ง
Which desiccant does a better job protecting tools and electronics?
We built a test using humidity sensors, an Arduino, and Python to find out.
๐ฅ Watch the full experiment: buff.ly/Gm0VSKX
#Engineering #Electronics
35
What's in an engineer's pockets? ๐๐ ๏ธ
A quick look at my everyday carry and the things I like to keep handy.
What's the one item you never leave home without?
#EDC #Engineering #Tools
18
I hunt electronic faults with a spray can. ๐ฅถ
Freeze spray lets me cool small areas of a circuit and watch for repeatable changes. It's great for tracking down intermittent problems and testing temperature sensors.
What's your favorite troubleshooting trick?
#Electronics
20



