Tτ (@teraytech) header
Tτ (@teraytech) profile picture

Engineer | Tests & Measurements & Metrology Enthusiast

Joined February 2016
Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)Photo by Tτ (@teraytech)
1
5
263
1
1
5
213
Delingha Prism Tower , China (Concentrated Solar Power Plant)
1
2
30
752
Introducing my new HAROGIC VNB-60 6GHz VNA 😋
7
9
105
3,639
It works so well, love it a huge improvement over libreVNA and the ECAL kit is a huge bonus too
3
430
Offer accepted! 🥳
66
11
5
805
18,178
Turned a WiFi 7 router into a 320Msps SDR. Custom firmware on its MediaTek MT7996 streams raw 14-bit IQ from 2.4/5/6GHz over 10GbE without dropping samples. It's not a snapshot mode, the waterfall is just one thing reading the stream. github.com/h0m3us3r/w1700k-s…
57
283
37
2,153
182,594
⋆⸜\ ꙳⋆新作アバターのお知らせ ⋆꙳/⸝⋆ 新作アバター『ソルト -Salt-』🐟🩶 ラスクのきょうだいです🐾꙳⋆ ✧2026年11月発売予定✧
88
8,437
2,398
28,147
1,699,103
Tτ retweeted
オフ会って感じ😙 楽しい
1
5
30
601
we built a lightning strike detector in just 2 days in partnership with @embedder_dev and open sourced it! the future of hardware is fast. a thread 🧵
55
132
15
1,770
167,633
Don't remove the screw that fixes the port on the shell, and you can get this👇
Oh fuck. A literal teardown 😭
5
3
96
7,722
I designed a miniature, four-quadrant, high-voltage power supply that employs digital pre-regulation and a Class-AB output stage to achieve high-efficiency, precision output; it is primarily intended to provide bias voltage for the compensation electrode of an ionization chamber.
6
29
1
364
14,730
I think most of the error comes from not using a proper 4-wire Kelvin shunt. The 5 mOhm resistor may not be very accurate either, and it seems to drift as it heats up under a long heavy load. All these errors add up and make the readings drift even more.
1
18
1,819
PCB showed up yesterday. I soldered it this morning, connected it to my bench, fired up Codex, and a little while later... the firmware was done. 😄 4 days from PCB design to working firmware.
Today's project: XT60 Power Meter with an LM5060 + N-MOSFET high-side load switch, designed for testing batteries and other power electronics. I was going to buy one... but then I realized none of them had a high-side switch. So I built my own.
1
8
117
5,501
It’s just like modern EVs ditching physical buttons. But for VNAs that cost $ 10-100k, Zero idea what the designers were thinking.
so how do you feel about soft/screen front panels?
9
7
93
5,281
Today's project: XT60 Power Meter with an LM5060 + N-MOSFET high-side load switch, designed for testing batteries and other power electronics. I was going to buy one... but then I realized none of them had a high-side switch. So I built my own.
4
6
1
151
11,489
The LM5060 monitors UVLO, OVP, and OCP, and cuts off the power path instantly if anything goes wrong. It's perfect for battery charge/discharge testing, and it has automotive-grade models
8
838